Print pagePDF pageEmail page

healthantenna-fab-400The magnetical coil

  1. Prepare a piece of AWG14 copper wire, 1.20m long, one strand
  2. Coil the wire in a clockwise direction around a rod of 6.4mmØ with 45 turns. If you are using a Battery-drill, use it in forward direction
  3. then widen the gap between the windings slightly by forcing a knife with the blunt side between the windings and moving the drill in reverse direction.
  4. Flatten the upper end of the coil with a hammer and split is lengthwise with a metal scissor. Bend one end round towards itself and leave the other one straight up in the air.

The gravitational coil

  1. Prepare a piece of AWG14 copper wire, 0.70m long, one strand
  2. Coil the wire in a clockwise direction around a rod of 2.8mmØ with 45 turns. If you are using a Battery-drill, use it in forward direction
  3. then widen the gap between the windings slightly by pulling the coil in both directions holding it each end with plyers.
  4. Flatten the upper end of the coil with a hammer and split is lengthwise with a metal scissor. Bend one end round towards itself and leave the other one straight up in the air.

The center pin

  1. Prepare a piece of AWG18 copper wire, 0.30m long, one strand
  2. Bend the wire into two equal halfs; arrest the bend into a wise grip and turn the other two ends with a battery drill in clockwise direction (forward speed). Turn until you have made a nice braid, the number of turns is not important.

Assembling the coils

  1. Insert the center pin into the gravitational coil with the round end of the pin next to the split and bend end of the coil.
  2. Insert both of them into the magnetical coil in the same direction. Now you should see the 3 pins together on the opposing end.
  3. Place the whole assembly into the test tube to see if you can easily close the plug; cut the pins if needed to fit.

Nano-coating

  1. Clean the assembled pieces either by torch fire or in a vinegar bath (do not forget to rinse thouroughly)
  2. Spray them with cold caustic solution put them in a sealed container and let the coating take place for 12 to 24hours

  3. Rinse and let dry
  4. Put some drops of cold caustic in the test tube, close it and let it be nano-coated as well for 12hrs

GaNS application

  1. Apply GaNS-CO2 on the tip of the magnetical coil, GaNS-CuO on the graviational and GaNS-CH3 on the center pin.


Put it all together

  1. Place a small piece of bees wax (not heated over 60ºC) into the test tube (16mm x 150mm) and let it melt in a waterbath
  2. Add the copper coils into the test tube and dip the plug into the liquid wax; close the testtube and let it all cool down
  3. Make a ring of heat glue around the plug and another one just beneath on the test tube; put a piece of heat shrink tube over the 2 rings and shrink them with a hot air gun

ant-typ-fab2-600

 

 

 

 

 

 


healthpen-fab-quicklist


Notes:

  • A coil that is turning cw takes energy away from the body; this is a good choice if we want to relieve the patient (sun stroke for example); a coil which runs ccw gives energy. Most of the application require a ccw turning coil.
  • You can dip the tip of the Healthpen testtube into a healing essential oil (or other natural healing substance) before the treatment; the antenna will then transmit these energies via the plasma current into the body of the patient.
  • Une bobine tourné dans le sens des aiguilles d’une montre enlève de l’énergie du corps, a un caractère soulageant (bon peut être dans le cas d’une insolation); une bobine tourné dans le contre-sens des aiguilles donne de l’énergie. La plus part des maladies sont accompagnées par un manque d’énergie.
  • Vous pouvez tremper la pointe de votre stylo dans des substances guérissantes comme des huiles essentielles; le stylo va transmettre l’énergie de ces substances par le courant du plasma dans le corps du patient.

buyit

Vous pouvez aussi acheter l’Antenne de bien-être ici

 


Antenne de bien-être spécifique

Elle est faite comme l’Antenne de bien-être de base, sauf que le GaNS appliqué sur la pointe de la tige centrale et/ou la bobine gravitationnelle est fait sur mesure pour le client (avec des ingrédients spécifiques ou/et échantillon d’urine).

buyitVous pouvez aussi acheter l’Antenne de bien-être spécifique ici


antenneurgence 300Antenne d’urgence

  1. Coupez un fil de cuivre (monobrin, AWG 14,1.50m/59po) pour la bobine magnétique.

  2. Coupez un fil de cuivre (monobrin, AWG 14, 1.20m/47po) pour la bobine gravitationnelle.

  3. Coupez un fil de cuivre (monobrin AWG 14, 0.15m/6po) pour la tige centrale.

  4. Utilisez le gabarit de double cone pour tourner la bobine magnétique, détachez le gabarit et enlevez la bobine. Vous pouvez acheter le gabarit ici.

  5. Pliez le fil de la bobine gravitationnelle en deux, faites une petite boucle avec un pince, serrez la boucle dans un étau, tourner les deux fils parallèle autour d’une tige Ø6mm et pliez les 2 pointes en parallèle.

  6. Pour le reste, procédez comme pour l’Antenne de base.

ant urg gab600
Gabarit de l’Antenne d’urgence
ant-urg-fab-600
Composants de l’Antenne d’urgence

 

 

buyitVous pouvez aussi acheter l’Antenne d’Urgence ici